How tight should toilet flange bolts be?

How do I stop my toilet bolts from spinning?

Toilet bolts that spin! How to stop them even if the toilet is already installed.

How do you tighten a flange bolt?

Flange Bolt Tightening – YouTube

How tight should toilet mounting bolts be?

As tight as you can go will probably snap the porcelain (with a good socket you can torque a nut onto a bolt quite a bit). Until you think it’s about to snap is just guessing. Snug. No movement.

Does a toilet flange need to be bolted?

Does a toilet flange need to be screwed or bolted to the floor? Yes, you have to screw or bolt the toilet flange to the floor. If you do not, you risk not securing the toilet enough to prevent rocking that may damage the wax seal, the drainage pipe, or the floor.

How do you secure a toilet flange bolt?

Kitchen &amp, Bathroom Repairs : How to Install Hold-Down Bolts on a Toilet

How long should toilet flange screws be?

1 1/2 inch screws or longer is usually a safer bet if you are screwing into thicker boards. If the board is more shallow, then 1-inch screws will probably do the job for you.

When tightening flange bolts you should use a?

When tightening a four-bolt flange, use a criss-cross pattern.

Should I torque the nut or bolt?

In simple terms, you need torque to create tension in a bolt. You use torque to turn a nut onto a bolt and then to stretch the bolt, making it a solid spring that clamps the two materials together.

What does torquing a bolt mean?

Torque is the amount of energy it takes to spin the nut up along the threads of a bolt. Force x Distance that is, put a 200-pound ironworker on the end of a two-foot spud and you have 400 foot-lbs. of torque. Tension is the stretch or elonga- tion in a bolt that provides the clamp- ing force in a joint.

Should there be a gap between toilet tank and bowl?

Most toilets have a space between the bottom of the tank and the top of the bowl anywhere from a ¼ of an inch to a ½ inch. Tighten too loosely and the tank will leak underneath the rubber washers and down the bolts, tighten too much and risk the tank cracking.

Is toilet tank supposed to wobble?

No, your toilet isn’t meant to wobble. It’s supposed to be sturdy and hold your weight comfortably. If your toilet is wobbly, you can check if some of the issues we’ve mentioned above might be the cause. If they are, you can try to DIY and if not, make sure you call on a professional plumber to fix it.

Why does my toilet rock side to side?

Toilets usually rock because they are not resting flush against the floor. Underneath the toilet base is a round toilet flange that connects the toilet to the drain pipe. If the flange is a little higher than the surrounding flooring, the toilet becomes raised slightly in the center, allowing it to rock to either side.

Should toilet flange be even with floor?

The optimum flange height to aim for is 1/4 inch above the finished floor. This typically allows for almost any type of wax ring to be used and still ensure a good seal. If you recently tiled or changed the bathroom flooring, the flange height is likely less than optimal.

Should you caulk around toilet flange?

1. Caulk prevents a fouling area. If mop water, bathtub water, or a less pleasant “bathroom liquid” gets underneath the toilet, there is no way to clean it up. Caulking around the base of the toilet will prevent this from happening.

Should a toilet be bolted to the floor?

Your toilet should be fixed to the floor using several bolts. Carefully unscrew the nuts and washers to help free the toilet. Your toilet may also have silicone around the base to make it more secure. Simply remove this silicone to free your loo.

How far apart are toilet flange bolts?

Standard Fixtures Bolt holes must be between 5-1/4” and 8” apart. You will also need at least 3/4” clearance from the center of the bolt holes to the back of the toilet tank.

Are toilet bolts universal?

Are Toilet Tank Bolts Sizes Standard? Toilet tank bolts help to seal your toilet tank such that it does not leak. They are durable and often in the same sizes and lengths. More often, toilet tank bolts are standard and will fit most types of toilet tanks.

How is a toilet anchored to the floor?

The toilet flange, also known as a closet flange, is the part of the toilet that secures the unit to the floor and connects to the drain pipe. Usually made of PVC, rubber or metal, this piece is circular in shape and usually secured in place with a few bolts.

Should you caulk around a toilet?

Caulk keeps your toilet secure the floor, and avoids any chance of injury or toilet malfunctioning. It’s actually required by the International Plumbing Code to caulk a toilet to the floor, and now knowing the reasoning behind it, why would you not want to?

Do toilet flanges screw in?

How to Replace a Toilet Flange | Toilet Repair | The Home Depot

Should toilet flange be on top of tile?

The toilet flange needs to be on top of the finished floor. Meaning the bottom edge of the flange needs to be on the same plane as the toilet. So if your toilet sits on the tile, the flange needs to be on top of the tile too. The spacing of the toilet exit “horn” and sealing surface is designed for this height.

When installing gaskets tighten each bolt?

All bolts should be tightened in one-third increments, according to proper bolting patterns. Make a final check pass at the target torque value moving consecutively from bolt to bolt. Re-torque 12 to 24 hours after initial installation.

Why is it important to use the proper bolt tightening sequence when torquing bolts on an engine?

Because the joint surfaces compress, tightening one bolt in the vicinity of another will affect the preload generated by the first bolt tightened. A good tightening sequence ensures that an even preload distribution is achieved in the joint (See Dia. A).

How do you calculate torque for a flange?

Using a calibrated torque wrench (Manual or Hydraulic Torque Wrench), flange bolt torque can be measured during flange assembly.

Applied Torque, T= (k∙f∙d)/12 in FPS Unit

  1. T=Torque in ft-lb.
  2. k=Dimensionless nut factor or tightening factor.
  3. f=axial force in pounds.
  4. d=Nominal bolt diameter in inches.

How do you tell if a bolt is over torqued?

What happens when you over torque a bolt? – YouTube

Should bolts be lubricated before torquing?

So, torque isn’t the true measure of bolt tightness—it’s tension. But lubrication on the bolt threads—and a whole host of other factors—can cause fluctuation in torque readings. So once you add a lubricant of any kind to the threads, all bets are off as to whether the same torque setting will truly secure the bolt.

Is it better to over torque or under torque?

With every nut and bolt that you use, it’s imperative to make sure that you don’t under- or over-tighten it. A well-calibrated torque tool will save you from this trouble, but if you’re still using standard wrenches, then there could be the risk of a nut or bolt that is too loose or too tight.

Should the toilet tank touch the wall?

There is no hard-fast rule about whether a toilet should touch the wall, as it is a matter of personal preference. Some people are okay with a toilet tank’s top touching the back wall, while others desire a minimum of one inch of space between the commode and the back wall.

What do you do with the space behind the toilet?

Filling The Empty Space Behind The Toilet

  1. Hang towels. …
  2. Install hooks for baskets. …
  3. Mount an open shelf. …
  4. Mount multiple shelves. …
  5. Mount baskets. …
  6. Mount a storage unit. …
  7. Create built-in shelving. …
  8. Add a storage tower.

How do you fill the space between toilet tank and wall?

To fix a gap between a toilet and the wall, it’s important to measure the distance, cut a piece of wood, and wedge it into the gap. You can then paint the wood to match everything around it. The second solution is to remove the toilet and replace it with the correct size.

How do I stop my toilet tank from wobbling?

Toilet Tank Loose – Toilet Tank Support – YouTube

What are toilet shims?

Toilet shims are thin plastic or rubber tabs that are used to level a toilet. You can also use homemade wooden shims or stainless steel coins. If a toilet is installed on an uneven floor or if the toilet flange is too high off the floor, the toilet will need to be shimmed.

How do you level a toilet flange?

Level Up An Out of Level Toilet Flange – YouTube

Can a toilet flange be too high?

When your toilet flange is too high, your toilet may leak water and rock back and forth when used. Both the leaking and the rocking can warp or break the floor. A leaking flange can also rot the subfloor and lead to the accumulation of mildew and mold.

How do you level a rocking toilet?

How to Repair a Rocking Toilet | Ask This Old House – YouTube

Do you put the wax ring on the toilet or the flange?

Whenever you remove a toilet for any reason, you will need to replace the wax ring seal between the toilet and the toilet flange (sometimes called a closet flange) attached to the floor. A wax seal is used because it resists mold and bacteria and retains its sealing ability after years of use.

Does toilet flange go inside or outside pipe?

Install a toilet flange on the outside. This can be done with a hammer and chisel. If the flange is cast iron with a rubber gasket, you should be able to remove the cast iron with a hammer and chisel, remove the rubber gasket with a sharp knife, then replace the gasket and the flange.

How do you raise the toilet flange after tiling the floor?

Toilet Flange Height After Tiling – YouTube

How high should toilet flange be above tile floor?

For those that don’t already know, the proper toilet flange height is when it’s flush with the top of the finished floor. The optimum height is about ¼ inch. It’s easier to get your flange flush with the floor if you lay your flooring before you install the flange.

Does clear caulk turn yellow?

After years of exposure to water and humidity, clear silicone can begin to yellow and blacken. This discoloration is caused by exposure to rust and the formation of mold. Removing the yellow from clear silicone can be accomplished at home without the need for expensive cleaning products.

Why does toilet leak at base?

Why is the toilet is leaking from the base? The leak is usually caused when the seal under the toilet fails. Below you’ll learn how to install a new wax gasket to create a watertight seal between the toilet and the closet flange and install a new flexible water-supply tube.